not another auction..

well yes its another auction....due to the rising cost of racing this year ive been forced to sell some of my prize possesions...
ive got 2 glyde lowerd decks,,one used and one brand new..the used one is in good condition it has been ridden the grip tape is scuffed a little but its never hit a gutter and the bottom isnt scrached..its got small cracks in the turn down that was fixed in the construction process.. which makes it a heavy board due to the extra reinforcing but its still a great deck and you wont break this puppie..
also pete the ledgend has offered a brand new deck,, we just have to give him a week to skate before construction begins..there are reserves on these boards in respsect of petes hard work....

2 flexdex,,1 jim rippey 36inch and 1 classic 30 inch,,the rippey has small chips on the tale and the classic a small one on the nose ...they're rad boards to ride

1 set of 83mm 75a flywheels these have been ridden but not hard and are pretty much just worn in..

1 set of black sector nineballs 76mm 75a these have been ridden once and still have the fresh lines..

1 set of scriber black tar carvers brand new in the box..

the auction will run for 1 week and all gear must go..the glyde decks will start at $140 second hand and $190 brand new..flexdex will stat at $50 each these are sick boards and were well sort after in their day,,id hope they'd go to a good home..flywheels $50...sectors $40...scriber $30...
all items are plus shipping..

so come on help your countrymen out and buy my shit.....happy bidding.. :)

Replies to This Discussion

Permalink Reply by Ash on June 10, 2009 at 12:42

i dont have any pics of it, a wide flat in the middle, with a nice sharp concave at the edges. not quite as severe as an evo, but the perfect foot lock concave.

Ian McGlynn said:

60 on the flywheels and 50 on the nineballs. also, what is the cave like on the glyde?

Premium MemberPermalink Reply by Ian McGlynn on June 10, 2009 at 13:40

hmmm so tempting

Permalink Reply by Paul on June 10, 2009 at 19:10

Hey Leeso,
im in for $65 on the flys
and save me going to the scriber site to try find out....what size and duro are the tar carvers
Cheers
P

Premium MemberPermalink Reply by leeso on June 10, 2009 at 19:54

hey paul...the carvers are 75mm and doesnt have a duro...a bit slow but sticky as..

Paul said:

Hey Leeso,
im in for $65 on the flys
and save me going to the scriber site to try find out....what size and duro are the tar carvers
Cheers
P

Permalink Reply by Joe on June 10, 2009 at 20:08

Leeso is the slight cracks on the glyde like under the resin layer not the very top surface?

Premium MemberPermalink Reply by leeso on June 10, 2009 at 20:11

its in the side mate but it has been strengthend and wont break or delam it just makes the board a little heavier..

Premium MemberPermalink Reply by pete hill on June 10, 2009 at 20:20

the cracks are on the outside radius of the rear curve where it levels out to the mounting platform, when the bamboo changed from a horizontal laminate to a vertical it behaved differently while being forced into the curves on the mould, i had a few of these rejects before i got it sorted again, none got sold. after some mucking around with them i realised they were still solid as the resin and glass still filled in any cracks as they happened so i reinforced two of them, one for myself and one for leeso, the extra resin and glass added weight but if any board is bullet proof this is it.

Permalink Reply by Joe on June 10, 2009 at 20:29

Ok no problems just checking, sounds promising thats for sure.

pete hill said:

the cracks are on the outside radius of the rear curve where it levels out to the mounting platform, when the bamboo changed from a horizontal laminate to a vertical it behaved differently while being forced into the curves on the mould, i had a few of these rejects before i got it sorted again, none got sold. after some mucking around with them i realised they were still solid as the resin and glass still filled in any cracks as they happened so i reinforced two of them, one for myself and one for leeso, the extra resin and glass added weight but if any board is bullet proof this is it.

Permalink Reply by Arran Pratt on June 10, 2009 at 21:22

I'll start the bidding on the flexdex classic 30..$50 and go $70 on the flywheels

Permalink Reply by brodie on June 10, 2009 at 21:25

ill put $190 on the new glyde. sick boards and ive wanted one since i saw you guys riding them at btb. if pete hasnt made it yet does that mean i can send a graphic to be put on it?

not another auction..

Replies to This Discussion

Search