Cre8ive Sk8

Replies to This Discussion

Premium MemberPermalink Reply by Matthys on June 7, 2010 at 17:43

you dont by chance have any sabre bushings do you ado????

• ▶ Reply

Permalink Reply by Adrian Alderson on June 7, 2010 at 20:08

No, sorry. Not too sure if they will sell them seperate to the trucks. Waiting to see if someone starts to import the Sabre gear.

Matthys van lille said:

you dont by chance have any sabre bushings do you ado????

• ▶ Reply

Permalink Reply by Tommo on June 11, 2010 at 16:55

Hey ado just wondering is u had any Rodger bros dh36 decks left, if so how much am I looking at?

• ▶ Reply

Permalink Reply by Adrian Alderson on June 11, 2010 at 20:36

Yes, still got a couple $210 delivered

Tommo said:

Hey ado just wondering is u had any Rodger bros dh36 decks left, if so how much am I looking at?

• ▶ Reply

Permalink Reply by Tommo on June 11, 2010 at 21:35

Ok thanks heaps might call u soon

• ▶ Reply

Permalink Reply by Cooked on June 12, 2010 at 12:07

Hey Ado, do you sell single destructo trucks?

• ▶ Reply

Permalink Reply by Adrian Alderson on June 12, 2010 at 17:59

Sorry, no. I can only buy them in pairs and have never been asked for a single one before.

Callum Hogg said:

Hey Ado, do you sell single destructo trucks?

• ▶ Reply

Premium MemberPermalink Reply by Jack on June 16, 2010 at 15:17

hi ado
how much would i be looking at for:

Rayne Timeline OR landyachtz carbon mummy
Bennett 6.0's
angled risers
1/8th shock pads
2 sets of bolt hardware
O'Tang purple inheats.
some cheap but good bearings (bones reds or something) with spacers and speed rings
Sheet of Grip
a longer kingpin if needed for running venoms.

thanks for this.

• ▶ Reply

Permalink Reply by Adrian Alderson on June 16, 2010 at 21:50

Could do the Carbon Mummy for $380 delivered with all that gear, but think you'd be better off with a 180 truck (Randal, Paris, Grizzley) than the Bennett. The last couple of Timelines I have had have been badly drilled and ran off line so haven't bought any since.

Jack Nolan said:

hi ado
how much would i be looking at for: Rayne Timeline OR landyachtz carbon mummy
Bennett 6.0's
angled risers
1/8th shock pads
2 sets of bolt hardware
O'Tang purple inheats.
some cheap but good bearings (bones reds or something) with spacers and speed rings
Sheet of Grip
a longer kingpin if needed for running venoms.

thanks for this.

• ▶ Reply

Premium MemberPermalink Reply by Jack on June 16, 2010 at 23:58

hmmm. if you think the reverse kingpin would be better im happy to trust your judgement.

i was looking at the angled risers and those wheels because i thought the bennetts would need the risers and be really good for pumping so i probably dont need the risers. would those wheels work really well or would you reccomend others above them?

thanks

Adrian Alderson said:

Could do the Carbon Mummy for $380 delivered with all that gear, but think you'd be better off with a 180 truck (Randal, Paris, Grizzley) than the Bennett. The last couple of Timelines I have had have been badly drilled and ran off line so haven't bought any since.

Jack Nolan said:

hi ado
how much would i be looking at for: Rayne Timeline OR landyachtz carbon mummy
Bennett 6.0's
angled risers
1/8th shock pads
2 sets of bolt hardware
O'Tang purple inheats.
some cheap but good bearings (bones reds or something) with spacers and speed rings
Sheet of Grip
a longer kingpin if needed for running venoms.

thanks for this.

• ▶ Reply

Permalink Reply by Joe on June 27, 2010 at 19:39

Jack,
Still go with the risers even if you get reverse kingpin trucks. They'll pump/carve like a dream if set up right. The inheats would of probably been to big for setting them up on bennets, I'd go with a 4prez 70mm otang wheel or something around the 70mm's like mini hawgs and zigzags. The smaller wheels willl work best on that setup. Hope that helped out ;)
Just give Ado a call when your ready to order. He'll hook you up alot quicker and get it shipped then waiting for replies on ASRA :-)

• ▶ Reply

Premium MemberPermalink Reply by Jack on June 28, 2010 at 11:08

thanks joe thats really helpful, i talked to him via pm and he doesnt have any mummies in stock atm so ill just wait a bit.

Joe said:

Jack,
Still go with the risers even if you get reverse kingpin trucks. They'll pump/carve like a dream if set up right. The inheats would of probably been to big for setting them up on bennets, I'd go with a 4prez 70mm otang wheel or something around the 70mm's like mini hawgs and zigzags. The smaller wheels willl work best on that setup. Hope that helped out ;)
Just give Ado a call when your ready to order. He'll hook you up alot quicker and get it shipped then waiting for replies on ASRA :-)

• ▶ Reply

▶ Reply to Discussion

• ‹ Previous
• 1
• …
• 27
• 28
• 29
• 30
• 31
• …
• 87
• Next ›
• Page