ASRA - Australian Skateboard Racing Association

beaq trucks :(

i have beaq trucks for my landyachtz evo, long  long long story short i loosened the trucks regularly to have fun and slide, and as i was trying to tighten them for a hill, they wouldn't tighten cause all the thread in the bolt had been shaved off. only reason i can think that this happened was cause i loosened and tightened them alot, still unless beaqs are made to break this shouldn't of happened.

 

PLEASE TELL ME UR OPINION AND SUGGESTIONS   

Views: 983

▶ Reply to This

Replies to This Discussion


Premium MemberPermalink Reply by Tom Radinski on April 18, 2011 at 3:03
Get a new kingpin, end of thread.

Premium MemberPermalink Reply by Fendy on April 18, 2011 at 3:22
You got a bad kingpin. Get a new like like Tom said. No use complaining about a measly kingpin... lol. And it's bear, not beaq

Premium MemberPermalink Reply by Tom Radinski on April 18, 2011 at 7:20
you threaded the bolt, probably scratched up the thread on a curb or put the nut on at an angle once and fcked it, just replace it and be more careful next time, common sense
Permalink Reply by Robbo on April 18, 2011 at 7:20

Buy some new kingpins. Grade 8  Than you can spend another 6 months twisting the thread off before you will need some more

 

Permalink Reply by Robbie Atkin on April 18, 2011 at 10:14
BEAR not beaq

Premium MemberPermalink Reply by ben halls on April 20, 2011 at 18:22

wat bears cause me bears the kingpin is welded on i know thatis pretty is fixed but just sayin



Fendy said:

You got a bad kingpin. Get a new like like Tom said. No use complaining about a measly kingpin... lol. And it's bear, not beaq

Premium MemberPermalink Reply by Fendy on April 20, 2011 at 18:25
What??

ben halls said:

wat bears cause me bears the kingpin is welded on i know thatis pretty is fixed but just sayin



Fendy said:

You got a bad kingpin. Get a new like like Tom said. No use complaining about a measly kingpin... lol. And it's bear, not beaq

Premium MemberPermalink Reply by Steve on April 20, 2011 at 18:44

Translation - Which bears? Because my bears have a kingpin that is welded on or at least pretty much fixed to the baseplate. Just letting you know

 

After a couple of years dealing with groms I can confidently say that I am fluent in lazy grom type speak haha


Premium MemberPermalink Reply by Fendy on April 20, 2011 at 18:57

Haha cheers Steve. I guess I gotta start learning some gromlish. 

 

I have '08 grizzlies and the kingpin can be removed pretty easily. I've been using the same kingpin since '08 and it's still good as new (for a 3yo kingpin). I ride it pretty much everyday. 


Premium MemberPermalink Reply by Steve on April 20, 2011 at 19:57

No don't do it, even if your fluent in gromlish, you will still find yourself wanting to headbutt the nearest wall when reading it

( sorry groms! )

 

I have the bears in question and you can easily tap out the kingpin with a hammer and replace them with a decent length kingpin ( ask Robbo at Hopkins ) A standard kingpin fits in perfectly after the pressed kingpin is removed allowing you to put some sweet bushings in there.


Premium MemberPermalink Reply by Skittles on April 20, 2011 at 20:45
if they are 840's, sell them to me and get new ones... they can't be fixed <.< ... >.>  :p
Permalink Reply by Davin Gemmell on April 20, 2011 at 22:25


Fuck Steve you cracked me up with that comment.  I have kids at work who send me texts like this and usually have to read them 4 or 5 times to make out the shit they're dribbling

 


Steve said:

No don't do it, even if your fluent in gromlish, you will still find yourself wanting to headbutt the nearest wall when reading it

( sorry groms! )

 

▶ Reply to Discussion

RSS

Search

© 2025   Created by Bugs.   Powered by

Badges  |  Report an Issue  |  Terms of Service